A network administrator has configured two switches, named London and Madrid, to use VTP． However, the switches are not sharing VTP messages． Given the command output shown in the graphic, why are these switches not sharing VTP messages? [*] The VTP version is not correctly configured． The VTP operating mode is not correctly configured． The VTP domain name is not correctly configured． VTP pruning mode is disabled． VTP V2 mode is disabled．

What is the maximum data rate specified for IEEE 802．11b WLANs? 10 Mbps 11 Mbps 54 Mbps 100 Mbps

While troubleshooting a connectivity problem, a network administrator notices that a port status LED on a Cisco Catalyst series switch is alternating green and amber． Which condition could this indicate? The port is experiencing errors． The port is administratively disabled． The port is blocked by spanning tree． The port has an active link with normal traffic activity．

Two routers named Atlanta and Brevard are connected by their serial interfaces as shown in the exhibit, but there is no data connectivity between them． The Atlanta router is known to have a correct configuration． Given the partial configurations shown in the exhibit, what is the problem on the Brevard router that is causing the lack of connectivity? [*] A loopback is not set． The IP address is incorrect． The subnet mask is incorrect． The serial line encapsulations are incompatible． The maximum transmission unit (MTU) size is too large．

What can a network administrator utilize by using PPP Layer 2 encapsulation? VLAN support compression authentication sliding windows multilink support

Which three statements are correct about RIP version 2? It has the same maximum hop count as version 1． It uses broadcasts for its routing updates． It is a classless routing protocol． It has a lower default administrative distance than RIP version 1． It supports authentication．

The network shown in the diagram is experiencing connectivity problems． Which of the following will correct the problems? [*] Configure the gateway on Host A as 10．1．1．1． Configure the gateway on Host B as 10．1．2．254． Configure the IP address of Host A as 10．1．2．2． Configure the IP address of Host B as 10．1．2．2． Configure the masks on both hosts to be 255．255．255．224．

Which of the following describe the process identifier that is used to run OSPF on a router? It is locally significant． It is globally significant． It is needed to identify a unique instance of an OSPF database． It is an optional parameter required only if multiple OSPF processes are running on the router． All routers in the same OSPF area must have the same process ID if they are to exchange routing information．

Host 1 is trying to communicate with Host 2． The e0 interface on Router C is down． Which of the following are true? [*] Router C will use ICMP to inform Host 1 that Host 2 cannot be reached． Router C will use ICMP to inform Router B that Host 2 cannot be reached． Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached． Router C will send a Destination Unreachable message type． Router C will send a Router Selection message type．

Refer to the exhibit． The networks connected to router R2 have been summarized as a 192．168．176．0/21 route and sent to R1． Which two packet destination addresses will R1 forward to R2? [*] 192．168．194．160 192．168．183．41 192．168．159．2 192．168．183．255 192．168．179．4

Refer to the exhibit． Switch-1 needs to send data to a host with a MAC address of 00b0．d056．efa4． What will Switch-1 do with this data? [*] Switch-1 will drop the data because it does not have an entry for that MAC address． Switch-1 will flood the data out all of its ports except the port from which the data originated． Switch-1 will send an ARP request out all its ports except the port from which the data originated． Switch-1 will forward the data to its default gateway．

Refer to the output from the show running-config command in the exhibit． What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address? [*] Apply access-group 14 to interface FastEthernet 0/0． Add access-list 14 permit any any to the access list configuration． Configure the IP address of the FastEtherent 0/0 interface to 10．90．201．1． Add an interface description to the FastEthernet 0/0 interface configuration．

On point-to-point networks, OSPF hello packets are addressed to which address? 127．0．0．1 172．16．0．1 192．168．0．5 223．0．0．1 224．0．0．5

In order to allow the establishment of a Telnet session with a router, which set of commands must be configured? router(config)# line console 0 router(config-line)# enable password cisco router(config)# line console 0 router(config-line)# enable secret cisco router(config-line)# login router(config)# line console 0 router(config-line)# password cisco router(config-line)# login router(config)# line vty 0 router(config-line)# enable password cisco router(config)# line vty 0 router(config-line)# password cisco router(config-line)# login

In the implementation of VLSM techniques on a network using a single Class C IP address, which subnet mask is the most efficient for point-to-point serial links? 255．255．255．0 255．255．255．240 255．255．255．248 255．255．255．252 255．255．255．254

Refer to the exhibit． The network shown in the exhibit is running the RIPv2 routing protocol． The network has converged, and the routers in this network are functioning properly． The FastEthernet0/0 interface on R1 goes down． In which two ways will the routers in this network respond to this change? [*] All routers will reference their topology database to determine if any backup routes to the 192．168．1．0 network are known． Routers R2 and R3 mark the route as inaccessible and will not accept any further routing updates from R1 until their hold-down timers expire． Because of the split-horizon rule, router R2 will be prevented from sending erroneous information to R1 about connectivity to the 192．168．1．0 network． When router R2 learns from R1 that the link to the 192．168．1．0 network has been lost, R2 will respond by sending a route back to R1 with an infinite metric to the 192．168．1．0 network． R1 will send LSAs to R2 and R3 informing them of this change, and then all routers will send periodic updates at an increased rate until the network again converges．

Refer to the exhibit． The two exhibited devices are the only Cisco devices on the network． The serial network between the two devices has a mask of 255．255．255．252． Given the output that is shown, what three statements are true of these devices? [*] The Manchester serial address is 10．1．1．1． The Manchester serial address is 10．1．1．2． The London router is a Cisco 2610． The Manchester router is a Cisco 2610． The CDP information was received on port Serial0/0 of the Manchester router．

Which two values are used by Spanning Tree Protocol to elect a root bridge? amount of RAM bridge priority IOS version IP address MAC address

Refer to the exhibit． Router1 was just successfully rebooted． Identify the current OSPF router ID for Router1． [*] 190．172．32．10 208．149．23．162 208．149．23．194 220．173．149．10

How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates? Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface． Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic． Configure many sub-interfaces on the same subnet． Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces．

Refer to the exhibit． Which switch provides the spanning-tree designated port role for the network segment that services the printers? [*] Switch1 Switch2 Switch3 Switch4